|
05-25-2014, 03:47 PM
|
#1
|
Junior Member
Join Date: Oct 2013
Posts: 22
|
Door stop adjustment
The coach door pressure/hydraulic stop allows the door to swing open too far on our 2014 Solera. This is not a big problem unless the awning is down/extended......then door door slams into the awning arm which has chipped the paint on the door. I cannot see any way to adjust the door stop (such as the ones we have on our screen doors at home) . The stop is cylinder in shape and mounted at bottom of door. Suggestion?
Thank you
Dale
|
|
|
05-25-2014, 03:56 PM
|
#2
|
Senior Member
Join Date: Jul 2010
Posts: 7,948
|
Quote:
Originally Posted by rdjjef
The coach door pressure/hydraulic stop allows the door to swing open too far on our 2014 Solera. This is not a big problem unless the awning is down/extended......then door door slams into the awning arm which has chipped the paint on the door. I cannot see any way to adjust the door stop (such as the ones we have on our screen doors at home) . The stop is cylinder in shape and mounted at bottom of door. Suggestion?
Thank you
Dale
|
You just may have to get FR to replace with a shorter throw.
|
|
|
05-25-2014, 04:34 PM
|
#3
|
Senior Member
Join Date: Sep 2010
Posts: 196
|
If you change the mounting point of the strut on the door itself , you should achieve your goal. Moving the point of attachment to the door farther out should reduce the swing of the door. I looked at ours, and it looks pretty straight forward.
MIke
|
|
|
05-25-2014, 06:16 PM
|
#4
|
Senior Member
Join Date: Mar 2014
Posts: 1,748
|
Quote:
Originally Posted by rdjjef
The coach door pressure/hydraulic stop allows the door to swing open too far on our 2014 Solera. This is not a big problem unless the awning is down/extended......then door door slams into the awning arm which has chipped the paint on the door. I cannot see any way to adjust the door stop (such as the ones we have on our screen doors at home) . The stop is cylinder in shape and mounted at bottom of door. Suggestion?
Thank you
Dale
|
I just looked at my 2012, the swing of the door is about 90 degrees from closed. The cylinder is mounted at the top on the '12. The door, being 90 degrees, can't hit the awning support arm, in any extended position on my unit. Does yours swing greater than ninety?
|
|
|
06-01-2014, 05:59 PM
|
#5
|
Junior Member
Join Date: Oct 2013
Posts: 22
|
I think it is slightly more than 90 degrees.
|
|
|
06-01-2014, 06:11 PM
|
#6
|
Mod free 5er
Join Date: Mar 2008
Location: Concord, NC
Posts: 24,702
|
Quote:
Originally Posted by rdjjef
I think it is slightly more than 90 degrees.
|
Unhook it from the door and move the door to where it doesn't hit the arm and you will know how far to move the anchor out on the door.
__________________
|
|
|
06-01-2014, 08:19 PM
|
#7
|
Senior Member
Join Date: Mar 2014
Posts: 1,748
|
The doors I believe are all pre drilled, so was something mfg wrong?
|
|
|
06-02-2014, 03:11 PM
|
#8
|
Robert Mayberry
Join Date: Jan 2012
Location: Point Richmond
Posts: 94
|
Coach door stop
That door stop is a problem to begin with in that it is quite flimsy. Mine has ripped out of the door a couple times in a gust of wind. It takes very little wind to damage it and I'm not quite sure what to do.
Any ideas out there?
Bob
SanFrancisco
2011 24S
|
|
|
06-02-2014, 06:30 PM
|
#9
|
Senior Member
Join Date: Mar 2014
Posts: 1,748
|
If your asking about the plastic end being damaged due to a wind gust, I know you can buy replacement ends, to effect repair. The door should open with the piston acting as a damper until it opens to its full position.
|
|
|
06-02-2014, 06:38 PM
|
#10
|
Mod free 5er
Join Date: Mar 2008
Location: Concord, NC
Posts: 24,702
|
Quote:
Originally Posted by robertmayberry
That door stop is a problem to begin with in that it is quite flimsy. Mine has ripped out of the door a couple times in a gust of wind. It takes very little wind to damage it and I'm not quite sure what to do. Any ideas out there? Bob
|
The screws on the door were loose on mine when I picked it up from the dealer. Moved both anchors 2-1/2" toward the hinge and used 3/16" pop rivets on the door and it's held and still holding after 2 years.
__________________
|
|
|
06-28-2014, 06:41 PM
|
#11
|
Junior Member
Join Date: May 2013
Location: Saint Augustine, FL
Posts: 11
|
Door stop adjustment
Quote:
Originally Posted by rdjjef
The coach door pressure/hydraulic stop allows the door to swing open too far on our 2014 Solera. This is not a big problem unless the awning is down/extended......then door door slams into the awning arm which has chipped the paint on the door. I cannot see any way to adjust the door stop (such as the ones we have on our screen doors at home) . The stop is cylinder in shape and mounted at bottom of door. Suggestion?
Thank you
Dale
|
I too had the same problem after a short while of door use on my 2015 24R.
What I noticed is the door opener piston was actually loose and could be turned in a clockwise motion to tighten. This lessened the door travel to where it would no longer bump into the awning.
|
|
|
06-28-2014, 07:03 PM
|
#12
|
Senior Member
Join Date: Mar 2014
Posts: 1,748
|
Quote:
Originally Posted by Gman53
I too had the same problem after a short while of door use on my 2015 24R.
What I noticed is the door opener piston was actually loose and could be turned in a clockwise motion to tighten. This lessened the door travel to where it would no longer bump into the awning.
|
So, your saying you can spin the piston while in its fastened position, and the travel of the piston decreases. Can you explain how the adjustment process works. Thanks
|
|
|
06-28-2014, 07:10 PM
|
#13
|
Junior Member
Join Date: May 2013
Location: Saint Augustine, FL
Posts: 11
|
Door stop adjustment
Quote:
Originally Posted by Still Kickin
So, your saying you can spin the piston while in its fastened position, and the travel of the piston decreases. Can you explain how the adjustment process works. Thanks
|
Yes, that's correct. I was able to spin the piston in a clockwise motion and hence it lessened the travel distance.
On my model, the door stop is located at the bottom of the door and is fastened to the door threshold. At the point of the threshold connection is where I "tightened" the piston by turning it clockwise.
|
|
|
06-29-2014, 09:15 PM
|
#14
|
Junior Member
Join Date: Oct 2013
Posts: 22
|
Thanks for all the comments and suggestions. I just moved the mounting point on the door as suggested by MikeA and that fixed it. I will take a closer look at piston closer and see if end spins clock wise and changes its range of motion.
RDJJEF
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|