|
10-13-2018, 08:38 PM
|
#1
|
Junior Member
Join Date: Aug 2018
Posts: 8
|
A Frame rotten floor/wall
Hi everyone,
I have a Flagstaff T12RB A frame hard side camper;
I have discovered a have some rot in my floor. It is located under the bed frame. The previous owner added an exterior box in back. He secured it to the bumper and TRIED to secure it to the camper. Big mistake! He made two holes, water got in leaked down the wall. long story short, i had to remove all along the back wall (under the bed frame) and up one side (door side) from the back to the wheel well and 16" wide to ensure that i would be able to screw back onto the frame.After much debate and research, i used 5/8 PT plywood.
Pictures 1-4 are the past rot and repaired sections (4th being the repaired section).
Fast forward to last night and a massive down pour of rain. Checked on my caulking job and floor replacement. Everything is dry!
**Except a new leak!!
i have now discovered water is coming in around the screw holes for the spare tire and 3 of 5 lights.
Needed to see the extent of the damage, so fast forward to having to tear out all the wood paneling...more rot.
I will replace all the wood.
The wood around where the spare tire bolts entered has rotten, so I started to remove it all.
***Here comes the bad part
as i was cutting that center "beam" out (that held the spare tire bolts),it snapped back. It is under tension! Its the piece that two rods go into (or behind)?
what did I do and how do I fix it?
Pictures 5-9 are the current job.
5 and 6-the cut out of the panelling under the bed frame
7 and 8 - (sorry, their side ways) and the new rotted sections.
The “rods” are the white and black
9-where the white rod connects to the roof/wall
|
|
|
10-13-2018, 08:48 PM
|
#2
|
Senior Member
Join Date: Aug 2014
Location: Northern KY
Posts: 5,724
|
Pictures and lots of them would help muchly...
__________________
"nothing can now be believed which is seen in a newspaper. Truth itself becomes suspicious by being put into that polluted vehicle."
Thomas Jefferson to John Norvell pg. 2, June 11, 1807
2014 Shamrock 183
2014 RAM 1500 Bighorn Crew Cab, HEMI, 3.21 gears, 8 Spd, 4X4 TST TPMS
|
|
|
10-13-2018, 09:17 PM
|
#3
|
Junior Member
Join Date: Aug 2018
Posts: 8
|
Quote:
Originally Posted by rsdata
Pictures and lots of them would help muchly...
|
I edited my posted and pictures have been added
|
|
|
10-13-2018, 09:36 PM
|
#4
|
Senior Member
Join Date: Aug 2014
Location: Northern KY
Posts: 5,724
|
so which picture shows the under tension part? I can't make it out if there is one.
Maybe the second last and last picture?
can't you just fasten the cut in two piece back together again? It appears that board is in good shape. Some Gorilla glue, some clamps and a good piece of wood should do it.
__________________
"nothing can now be believed which is seen in a newspaper. Truth itself becomes suspicious by being put into that polluted vehicle."
Thomas Jefferson to John Norvell pg. 2, June 11, 1807
2014 Shamrock 183
2014 RAM 1500 Bighorn Crew Cab, HEMI, 3.21 gears, 8 Spd, 4X4 TST TPMS
|
|
|
10-13-2018, 09:59 PM
|
#5
|
Junior Member
Join Date: Aug 2018
Posts: 8
|
Quote:
Originally Posted by rsdata
so which picture shows the under tension part? I can't make it out if there is one.
Maybe the second last and last picture?
can't you just fasten the cut in two piece back together again? It appears that board is in good shape. Some Gorilla glue, some clamps and a good piece of wood should do it.
|
The piece I cut out has rot in it. But I will do something like that to repair
|
|
|
10-15-2018, 06:52 PM
|
#6
|
Senior Member
Join Date: Feb 2016
Posts: 214
|
The rods are springs that assist when lifting the roof. You will have the cut the bungee cords up on the roof and open both roof panels one at a time to 90 degrees so you can remove the spring on each side until you have the rear wall rebuilt. There are four springs, two front two rear, when you cut that support you let the bottom of the spring move into a more relaxed position. Here is a link to a video from a Chalet A frame torsion spring replacement which is similar and should help, may as well replace the springs while its apart, they are pretty cheap.
https://youtu.be/cbz6_-PxZ7Q
|
|
|
10-15-2018, 06:58 PM
|
#7
|
Junior Member
Join Date: Aug 2018
Posts: 8
|
Quote:
Originally Posted by sundancer330
The rods are springs that assist when lifting the roof. You will have the cut the bungee cords up on the roof and open both roof panels one at a time to 90 degrees so you can remove the spring on each side until you have the rear wall rebuilt. There are four springs, two front two rear, when you cut that support you let the bottom of the spring move into a more relaxed position. Here is a link to a video from a Chalet A frame torsion spring replacement which is similar and should help, may as well replace the springs while its apart, they are pretty cheap.
https://youtu.be/cbz6_-PxZ7Q
|
Thanks for the help!
I did manage to pull it back into place and repair the the “beam”
|
|
|
10-16-2018, 05:29 AM
|
#8
|
Senior Member
Join Date: Jun 2013
Location: London, Kentucky
Posts: 630
|
I really enjoy this type of post. Here is a member who finds a problem, comes to the forum asking for help/advice, shows what he/she has accomplished, repairs the rig and life goes on. No blame or insults hurled at FR.
Thank you chaulkie91, great job, best wishes.
Travel safe
__________________
2019 Ford F-350 Super Duty CC Dually 6.7 Diesel
2011 Cedar Creek 36CKTS Touring Edition
I Catch Fish......What is your SuperPower?
|
|
|
|
Thread Tools |
|
Display Modes |
Linear Mode
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|