|
02-16-2017, 02:07 PM
|
#1
|
Member
Join Date: Jun 2016
Location: Brooklyn Michigan 49230
Posts: 56
|
2017 19' ROO tongue jack
If I buy a electric tongue jack my question is can I install it and how do I wire it, a friend said he thought that it used a 7 way plug and you just plugged it into your truck plug?????? another guy said he hooks his up to the RV battery with a couple of clamps like on the jumper cables, and last of all where is the best place to buy one and about what do they cost?????
|
|
|
02-16-2017, 02:12 PM
|
#2
|
Senior Member
Join Date: Apr 2013
Location: Central New York
Posts: 1,165
|
The wiring is pretty simple - you just have two 12 volt wires. You can connect the negative to the frame or tie in to the wires on the tongue and same thing for the positive. Just tie it in to the existing wiring or directly to the battery. If you do tie in to existing wiring, make sure it is upstream of the battery disconnect switch if you want to have power to the jack when the disconnect switch is open (which is how the factory wires them). Fairly simple project that is really worth it. Just seal up your connections so they are weather tight
__________________
2022 Columbus 379MBC (Previous 2013 Rockwood Roo 23 IKSS)
2023 F-350 (Previous 2017 F250, 2005 F-150)
|
|
|
02-16-2017, 02:14 PM
|
#3
|
Site Team
Join Date: Jan 2007
Location: Goodyear, Arizona
Posts: 33,855
|
Takes about 30" to install.
It hooks up to the trailer's battery, NOT the truck. Your friend doesn't know what he's talking about.
Three bolts and positive wire to battery and negative wire to the frame.
Bought my Ultra Fab 3500 refurbished jack on Ebay for $99.
__________________
Dan-Retired California Firefighter/EMT
Shawn-Musician/Entrepreneur/Wine Expert
and Zoe the Wonder Dog(R.I.P.)
2016 PrimeTime TracerAIR 255, pushing a 2014 Ford F150 SCREW XTR 4x4 3.5 Ecoboost w/Max Tow Package
4pt Equal-i-zer WDH and 1828lbs of payload capacity
|
|
|
02-17-2017, 05:17 PM
|
#4
|
Senior Member
Join Date: Apr 2008
Location: West Valley City, Utah
Posts: 551
|
Simple process. Hook trailer onto tow vehicle & lower the jack so weight is off of the jack. Unbolt the old tongue jack (3 bolts). Put new jack in place. Tighten 3 bolts. Hook wire or wires to battery. Simple process. Most jacks will have instructions to help you, but it isn't hard to do. You can buy electric jacks online or from local dealer or RV parts dealer.
__________________
2014 Chevy Silverado
2011 Rockwood Roo 233S
|
|
|
02-17-2017, 05:34 PM
|
#5
|
Senior Member
Join Date: Sep 2010
Location: Eastern Ontario
Posts: 4,167
|
__________________
Fonzie
2011 Rockwood 8319SS with ProPride 3P hitch/GoodYear Marathons/TST TPMS 507
2019 F350 Ruby Red 6.7l diesel 3.31 axle electronic locker
Yamaha 3000iseb generator:Progressive Ind. EMS-HW30C : Eastern Ontario
Nights Camped: 2014 (18) 2015 (18) 2016 (36) 2017 (32) 2018 (42) 2019 (28) 2020 (35)
|
|
|
02-18-2017, 02:15 PM
|
#6
|
Senior Member
Join Date: Nov 2014
Posts: 109
|
Friend Was Correct
Quote:
Originally Posted by bikendan
It hooks up to the trailer's battery, NOT the truck. Your friend doesn't know what he's talking about.
.
|
Sorry to say, his friend was right. I installed one and it came with a 7-pin plug and instructions for connecting to the TV. I didn't install it that way, I did connect directly to the battery.
__________________
2015 Rockwood A192HW
2011 KIA Sorento 6Cyl
|
|
|
02-18-2017, 03:19 PM
|
#7
|
Site Team
Join Date: Jan 2007
Location: Goodyear, Arizona
Posts: 33,855
|
Haven't seen one like that.
__________________
Dan-Retired California Firefighter/EMT
Shawn-Musician/Entrepreneur/Wine Expert
and Zoe the Wonder Dog(R.I.P.)
2016 PrimeTime TracerAIR 255, pushing a 2014 Ford F150 SCREW XTR 4x4 3.5 Ecoboost w/Max Tow Package
4pt Equal-i-zer WDH and 1828lbs of payload capacity
|
|
|
02-18-2017, 04:31 PM
|
#8
|
Senior Member
Join Date: May 2015
Location: Dunn, NC
Posts: 1,199
|
Jack wiring
Quote:
Originally Posted by bikendan
Takes about 30" to install.
It hooks up to the trailer's battery, NOT the truck. Your friend doesn't know what he's talking about.
Three bolts and positive wire to battery and negative wire to the frame.
Bought my Ultra Fab 3500 refurbished jack on Ebay for $99.
|
It was news to me also, but I did purchase one tongue jack that came with a 7 pin plug. Unplug camper, plug jack in to use. Way too complicated for me! I cur the plug off, ground eore to frame, hot wire to battery positive. 30 amp breaker on positive wire. Jack works while trailer still pluged in. So......anything is possiblw when it comes to re's.
|
|
|
02-18-2017, 04:37 PM
|
#9
|
Senior Member
Join Date: Nov 2014
Posts: 109
|
__________________
2015 Rockwood A192HW
2011 KIA Sorento 6Cyl
|
|
|
02-18-2017, 04:53 PM
|
#10
|
Site Team
Join Date: Jan 2007
Location: Goodyear, Arizona
Posts: 33,855
|
I wouldn't want to have to use the TV all the time, just to raise and lower the trailer.
__________________
Dan-Retired California Firefighter/EMT
Shawn-Musician/Entrepreneur/Wine Expert
and Zoe the Wonder Dog(R.I.P.)
2016 PrimeTime TracerAIR 255, pushing a 2014 Ford F150 SCREW XTR 4x4 3.5 Ecoboost w/Max Tow Package
4pt Equal-i-zer WDH and 1828lbs of payload capacity
|
|
|
02-18-2017, 05:34 PM
|
#11
|
Senior Member
Join Date: May 2016
Posts: 1,363
|
That would be for installations that don't have batteries on the trailer.
If installing on a camper (or any other trailer) with batteries, you would hard-wire to the trailer's electrical system.
|
|
|
02-19-2017, 09:00 AM
|
#12
|
Senior Member
Join Date: Jul 2014
Location: SouthWest Michigan
Posts: 5,977
|
Quote:
Originally Posted by bikendan
Takes about 30" to install.
It hooks up to the trailer's battery, NOT the truck. Your friend doesn't know what he's talking about.
Three bolts and positive wire to battery and negative wire to the frame.
Bought my Ultra Fab 3500 refurbished jack on Ebay for $99.
|
I think Dan meant 30 minutes !!! LOL !!!
And he is right on !!! If we still owned a TT I would not be with out one !!!
Best Moid you can do to a TT !!!
|
|
|
03-11-2017, 10:42 PM
|
#13
|
Senior Member
Join Date: May 2015
Location: Dexter, MI
Posts: 410
|
I'm looking at installing a power jack on my Roo 183 this year. I haven't looked at it yet, but I imagine that you must take into account how high the jack sits so it doesn't interfere with the front bed when lowered.
I think I read somewhere that the Brute jacks sit a bit too high.
Have to search through the forums, because I'm sure the answer is already here someplace.
__________________
Eric & Abby
2016 Rockwood Roo 183
2014 Ford Explorer Sport
|
|
|
03-12-2017, 09:19 AM
|
#14
|
Senior Member
Join Date: Jul 2014
Location: SouthWest Michigan
Posts: 5,977
|
We had a popup many years back,,,
never thought we needed a power jack with a popup !!!
Not like when you have a WDH !!!
|
|
|
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
|
» Recent Discussions |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|